Wall with AluStarTec aluminium panels

The light-weight, hand-set AluStarTec aluminium panels are best in class when it comes to weight-performance ratio. They have an aluminium frame and an all-plastic facing alkus. It links up to the AluStarTec steel panels with the idendical attachments and accessories and covers those areas where no crane is available. 

Scroll down this page to find a product list showing the parts you may need, when forming a wall with AluStarTec aluminium panels. Please note that the number of parts may vary according to the exact specifications. Contact us for advice, consultation, planning and support.  Find out more on our modular hand-set system AluStarTec on the product page

Contact Form

 
 
 

Product List

 
 
Formwork
Ties
Bracing
Safety
 
 
  • AS panels

    Construction height 12 cm, frame profile width 4 cm. Two tie holes per panel height 270 cm. Absolutely compatible with... 

  • ST aluminium filler

    Aluminium with high-quality annealed powder coating. With tie holes. For length compensation of 5 cm, especially in corners.... 

  • ST compensation plate

    Steel construction with steel sheeting. Primed and cavity-sealed. Is used to compensate gaps of 8 to 20 cm and attached to... 

  • AS timber profile

    Timber profile with groove. Is used for job-built fillers of 14 cm or more or to connect job-built formwork with 21 mm... 

  • AS inside corner AL

    Aluminium with high-quality annealed powder coating. For 90° corner configurations. Side length 25 cm. With tie holes. 

  • AS/ST outside corner

    Aluminium with high-quality annealed powder coating. Provides together with ST panels and AS assembly locks a fast and... 

  • AS hinged inside corner

    Steel construction with steel sheeting. Primed and cavity-sealed. Side length 30 cm. Adjustable angle 60°-180°. 

  • AS hinged outside corner

    Steel construction with steel sheeting. Primed and cavity-sealed. Side length 7,5 cm. Adjustable angle 60°-180°. 

  • ST stripping corner

    Steel construction with steel sheeting. Side length 25 cm. With tie holes. When the bell-crank lever is pushed upwards with... 

  • AS assembly lock

    Galvanized. Tightly connects and aligns AluStar and StarTec panels. Clamping length 8 cm.  

  • Uni-assembly lock

    Galvanized. For stepless compensation. Clamping length 22 cm or 28 cm. 

  • Combi-lock with coupling

    Galvanized. Is used to attach the push-pull props at the panel joint of the AluStar, StarTec, Mammut and Mammut 350 wall... 

  • Flange screw

    Galvanized. DW thread Ø 15 mm. Is used to attach accessories, e.g. alignment rails, brace frames, push-pull props, etc.... 

  • Door spindle MFS

    Steel, galvanized, DW 20. Adjustment range 700-1100 mm. Is used to brace door and window blockouts. With nail holes.... 

  • Alignment rail

    Galvanized. Is used to brace panel joints for crane ganging, bridge problem areas, brace compensation areas and build stop... 

  • Corner angle 40/60

    Galvanized. Side lengths 40 and 60 cm. For inside and outside corners. 

  • Stop end fixture 23/40

    Yellow chromated. Is used together with the EcoAs or StarTec multi-purpose panel to form outside corners and abutments. Is... 

  • Stop end bracket

    Galvanized. Is used to form stop ends. Suitable for frame profile widths 23 mm (EcoAs, AluFix), 40 mm (AluStar, StarTec)... 

  • Uni-tie claw

    Galvanized. Permits tieing directly above or beside the panels. Is suited for panels with a frame profile width of 40 mm... 

  • AS crane hook

    Is used to move panels. Self-locking. Load capacity: 15 kN (1,5 tons). Always 2 crane hooks required per gang. For use and... 

  • Transport angle 12

    Is used to stack and transport 5 to 12 frame formwork panels with a construction height of 12 cm and 12 cm hole distance.... 

  • Safety bolt

    Secures stacked panels. 

  • MevaTrenn pro

    Not shown. Suited for absorbent and non-absorbent forming faces.Solvent-based. Evaporates when applied, leaving avery thin... 

  • Sprayer

    Not shown. To allow for an even and sparing spraying of the forming surface, suited for (5 litre) MevaTrenn and wax. 

  • Concrete scraper

    With 6 or 10 replaceable hard-metal plates and steel ledge. Wooden stick (ash-tree) with handle. 

  • Beam clamp H20/H20

    Galvanized. Is used to attach planks or cross beams to H20 beams when using slab tables. 

 
 
  • Articulated flange nut 15/120

    Forged, galvanized. DIN 18216. DW thread Ø 15 mm, plate Ø 120 mm, max. inclination 10°, SW 27. Max. load capacity 90 kN.... 

  • Flange nut 100

    Forged, galvanized. DIN 18216. DW thread Ø 15 mm, plate Ø 100 mm, SW 27. Admissible load 90 kN. 

  • Spanner

    Inset yellow chromated. Spanner width (SW) 27 mm. Is used to tighten and loosen flange nuts 100, articulated flange nuts... 

  • Drive nut 60

    Galvanized. DW thread Ø 15 mm, plate Ø 60 mm. Adm. load capacity 90 kN (DIN 18216). Is used to tie the formwork to the... 

  • Tie rod DW 15/90

    Uncoated, not weldable. DW thread Ø 15 mm. Is used to tie panels of double-sided formwork. Adm. load capacity 90 kN (DIN... 

  • Tensioner AS/ST for foundation tape

    Galvanized. Connects the foundation tape to AluStar or StarTec panels and serves as bottom anchoring when panels are... 

  • Trolley for foundation tape

    Not shown. Is used to transport and cut foundation tapes to length. Suitable for one roll Pneumatic wheels. 

  • Plug D20

    Is used to close unused tie holes (AluFix, EcoAs, AluStar and StarTec). 

  • Stop end bracket

    Galvanized. Is used to form stop ends. Suitable for frame profile widths 23 mm (EcoAs, AluFix), 40 mm (AluStar, StarTec)... 

  • Pressure gauge

    Not shown. Measures tractive force of anchors from 250 to 400 kN. Includes compensating plate for tie rods, with 50 mm hole... 

  • Cone for plastic tube

    Available with 10 mm or 30 mm covering . 

  • Plug

    Is used to close tie holes in the wall when plastic tubes D22 or D30 are applied. Two plugs are required per tie hole.  

  • Water stop

    Uncoated. Lost part for tie rods DW 15 and DW 20 to produce watertight tie holes. Adm. load capacity depends on diameter: Ø... 

  • Uni-tie claw

    Galvanized. Permits tieing directly above or beside the panels. Is suited for panels with a frame profile width of 40 mm... 

  • Extractor for double-headed ground nail

    Not shown. Is used to remove the ground nail from the earth together with a lever rod (not supplied).  

 
 
  • Push-pull prop R

    Galvanized. Guarantees tensile and compression strength. Aligns and supports wall and column formwork. The footplate and... 

  • Braces SRL

    Galvanized. Guarantee tensile and compression strength. With right-hand and left-hand spindle and revolving centre part.... 

  • Brace frame 250

    Galvanized. Aligns and braces the formwork. Available with or without formwork-prop connector. Consists of a push-pull prop... 

  • Formwork-prop connector

    Galvanized. Connects braces, brace frames and push-pull props (max. Ø 48 mm) to the multi-function profile (with a flange... 

  • Universal joint connector 76/135

    Galvanized. With head bolt 16/90 and cotter pin 4. Is used to attach push-pull props to vertical or horizontal panel joints... 

  • Articulated foot plate

    Galvanized. With head bolt 16/90 and cotter pin 4. For push-pull props and braces of up to Ø 57 mm. 

  • Double-jointed foot plate

    Galvanized. With head bolt 16/90 and cotter pin 4. Serves as foot plate for brace frames 250 and as connector for braces and... 

  • Formwork-prop connector

    Galvanized. Is used to connect braces, brace frames and push-pull props (max. Ø 48,3 mm) to the multi-function profile with... 

  • Cotter pin 4

    Galvanized. Locks the head bolt. 

  • Combi-lock with coupling

    Galvanized. Is used to attach push-pull props at the panel joints of AluStar, StarTec, Mammut and Mammut 350 wall formwork.... 

  • Flange screw

    Galvanized. DW thread Ø 15 mm. Is used to attach accessories, e.g. alignment rails, brace frames, push-pull props, etc.... 

Worker protection is mandatory by law from a working height of 2 m. The working platform must be equippped with fall protection on all four sides.

MEVA safety systems offer you a flexible answer to safety requirements, compiled individiually to meet your project needs. Refer to the safety systems page and consult with us on the most effective and cost-efficient solution. 

  • Walkway bracket

    Galvanized, yellow, pluggable. Is used as a working and safety scaffold. Is attached to the multi-function profile and... 

  • Side railing

    Galvanized. Is plugged into the walkway bracket. 

  • Guard-railing post

    Galvanized. Is plugged into the walkway bracket. 

  • Guard-railing post 48

    Galvanized. With manifold to attach it to the walkway bracket, designed with tube Ø 48 mm to attach tube couplers. 

  • Support guard 800-railing post

    Galvanized. For the side protection at all MEVA wall formwork systems. Allows the extension for guard-railing KLK 230 and... 

  • Scaffold tube

    Galvanized. Is used as hand-rail / mid-rail in combination with guard-railing post 48. 

  • Upstand bracket

    Adjustment range 100 mm. Is used to brace upstand formwork. 

  • Plastic tube

    Is used as a plastic sleeve for a tie rod that is to be recovered and re-used. 2 m long.  

  • Planing cap DW

    Hard foam, 10 cm long, 45° end piece. For DW 15 and DW 20. Is plugged onto the DW tie rod or on a plastic sleeve for... 

  • Spiral anchor DW 15/100

    Steel spiral bead, 10 cm long, with styropore core. Is used to attach formwork equipment with tie rods DW 15, e.g. when... 

  • Folding access platform BKB 125

    Self-locking; ready-made platform with a foldable guard-railing and an overall width of 125 cm; it is supsended onto the... 

  • Folding access platform BKB 125/140

    It is used for inside corner configurations and length adjustments. In the latter case a side railing BKB 125 and two (2)... 

  • Side railing BKB 125

    Galvanized. Suited as side railing for all folding access platforms or as guard-railing for platform BKB 125/140. Is... 

  • Flange screw

    Galvanized. DW thread Ø 15 mm. Is used to attach accessories, e.g. alignment rails, brace frames, push-pull props, etc....