Areas with curved walls: Slide MD compensation beams (3) into the MD primary beams and place props with H20 beams (4) along the curved wall. Place the facing (2) for the filler area onto the MD compensation beams and H20 beams. Use several short H20 beams for wall curves with a small radius.
Other filler areas: Use H20 beams and a facing cut to size. Depending on the width of the filler area, the spacing of H20 beams may be limited to max. 50 cm.
(1) MevaDec panel
(5) Prop with drop head
Ground broke on the new One City Center, also known as the “Durham City Center” in Durham, North Carolina in February 2016.
Construction is underway on a complex of 489 villas in the Nad Al Sheba area of Dubai.
A prominent hotel and apartment complex is taking shape in Dubai’s Al Qusais district.
Al Mankhool is located in western Dubai and crossed by Al Mankhool Road, also referred to as Bank Street.
The Lagoons is set to be a signature development within Dubai’s booming property sector, with unique offerings and a strategic location.
Ramps, architectural-concrete walls and ceilings, numerous concrete beams, rectangular and oval columns, rounded outside corners and bevelled inside corners.
Saving much time, labour and inventory by fully utilising MevaDec’s and AluStarTec’s system flexibility.
Note that each building project will vary in terms of the number of parts needed. If you need assistance in planning the pour, please consult with us via the contact form.
The panel frames are made up of closed 2-chamber aluminium profiles and torsion-proof. Thanks to their high-quality annealed...
Aluminium with high-quality annealed powder coating. Primary beams and MD drop heads are the load-bearing system of MevaDec....
Aluminium profile with plastic nailing strips on top and at the bottom. Can be used in 2 ways: a) If used with the...
Galvanized, partly with high-quality annealed powder coating. A safety latch prevents disengagement. The MD drop head...
Galvanized, with high-quality annealed powder coating. Supports the MD panels and secures them automatically against...
Aluminium profile with high-quality annealed powder coating. Is equipped with a nailing to support job-built filler areas....
Galvanized. Tightly connects MD panels to each other and clamps MD compensation beams to MD panels. Clamping length 4,4 cm.
Galvanized. Permits support of primary beams where no drop head can be used, e.g. for intermediate support, at walls and...
Galvanized. Clamps planks to the bottom of primary beams. When using MEP props, the safety claw can be used to attach a...
Galvanized. Eases the assembly when applying the panel method. The panels are simply swung up and temporarily supported by...
Galvanized. Eases stripping of primary beams if these stick to the slab due to an increased concrete adhesion or inclined...
Galvanized. With chisel. Is used to clean the groove of the MD primary beam.
Spare part. Replaces the used blade of the cleaning scraper.
Plastic cover. Closes the gap between two MD panels when applying the drop-head-beam-panel method (FTE). Length 1,50 m.
Aluminium. Is attached to the groove of the primary beam and allows one person to level the slab formwork.
Is used to stack and transport 5 to 12 MD panels. Distance between holes is 14 cm. We recommend using 2 foldable angles and...
Is used to move MD panel stacks in transport angles 14 or in the MD transport rack (4 castors are required in either case)....
Galvanized. Is used to stack and transport up to 14 panels 160 x 80 cm. Two transport racks can be stacked...
Three-layer plywood forming face, 21 mm thick, with resistant coating on both sides. Good pore structure of the concrete due...
Not shown. Multi-layer plywood forming face, 21 mm thick, with film-coating on both sides and edge protection.
Not shown. For safety against wind load. 50 mm wide, reinforced loop 200 mm, cranked snap hook with safety flap, DIN EN...
Galvanized. Is attached to two wooden girders H20. With eyes to attach the tension belt.
Not shown. Eases formwork cleaning and is applied to the formwork parts not in contact with the concrete, e.g. panel frames....
Universal release agent that can be applied to all types of facing. Usable for civil engineering and building projects as...
Not shown. Suited for absorbent and non-absorbent forming faces.Solvent-based. Evaporates when applied, leaving avery thin...
Not shown. To allow for an even and sparing spraying of the forming surface, suited for (5 litre) MevaTrenn and wax.
A complete set for the repair of alkus facing. All items can also be ordered separately.
Galvanized. According to European Standard EN 1065, class E. Admissible load capacity 30 kN. Higher load capacities are...
Combination of steel inner tube and aluminium outer tube with T-groove to attach reinforcing frames. The SAS quick lowering...
Galvanized. According to the European Standard EN 1065 class D the admissible load capacity is 20 kN at any extension....
Galvanized. The forked prop head can be used as a support instead of a drop head at the beginning or end of a primary beam...
Galvanized. Is used to attach MD drop heads, MD prop heads of forked prop heads, etc. Pin 14/90 is used for steel tube props...
Galvanized auxiliary to stabilize props with Ø 48 to 80 mm. The turnable legs allow the tripod to be used in rooms, along...
Are used to attach MD drop heads and MD prop heads to the MD/ME props.
Robust multi-purpose girder for the most different tasks. While the girder itself does not weigh much, it has a high...
Galvanized. Is used to connect wooden H20 girders to each other. The wedge locks the girdes into place and releases them.
Prop according to standard EN 1065 class E. Steel inner tube and aluminium outer tube with T-groove to attach reinforcing...
Aluminium. Reinforcing frame that is required when building towers with MEP props. The frames are attached to the aluminium...
Aluminium profile (same as outer tube of MEP prop) with 2 foot plates. Is used to extend shoring towers. A plug connector...
Galvanized. Is used to connect MEP props and extensions. Together with 2 pins 14/135 the plug connectors provide a rigid...
Galvanized. Is used as foot plate for MEP props and extension pieces on sloped surface for perpendicular load transfer. Max....
Galvanized. Allows props beneath slab tables to be folded so that with a transport spreader the slab tables including props...
Is used to attach the MD beam to the prop or prop extension.
Galvanized. With DW thread to clamp stringers to the prop head. Is safely attached to the inner tube of MEP props with pins...
Galvanized. Adjustable cross-brace made of steel tubes. Is used for bracing when prop spacing varies. The two figures 170/90...
Galvanized. Is used to attach scaffold tubes Ø 48 mm to the aluminium outer tubes of MEP props or extension pieces.
Galvanized. Is used to attach push-pull props to the aluminium outer tube of the MEP props or extension pieces.
Galvanized. DW thread Ø 15 mm. Is used to attach props for horizontal bracing, e.g. in case of single-sided formwork....
Galvanized. Is used to lift and move shoring towers and slab tables. Height 2,12 m; load capacity 500 kg. Adjustment range...
Galvanized. Is used to move large shoring tower units. Length 2,4 m; load capacity 30 kN (3 tons); 4 wheels. The...
Galvanized, foldable. Max. load capacity 10 kN (1 ton). Is used to move slab tables with a crane. Length can be adjusted...
Forged, galvanized. DIN 18216. DW thread Ø 15 mm, plate Ø 100 mm, SW 27. Admissible load capacity 90 kN.
Galvanized. DW thread Ø 15 mm. Is used to move slab tables. Load capacity 10 kN (1 ton). Always 4 crane hangers are...
Galvanized. Is used to safely lock the plug connectors MEP at the profile of the MEP props and extension pieces, forked prop...
Galvanized steel spindle. Coarse adjustment with the G-hook, precise adjustment with the robust adjusting nut on the outside...
Not shown. Is used to attach MD drop heads or MEP spindles to the MEP props or extension pieces.
Worker protection is mandatory by law from a working height of 2 m. The working platform must be equippped with fall protection on all four sides.
MEVA safety systems offer you a flexible answer to safety requirements, compiled individiually to meet your project needs. Refer to the safety systems page and consult with us on the most effective and cost-efficient solution.
Galvanized. Is plugged into the MD support for panel or beam.
Galvanized. With manifold to be plugged into the walkway bracket and with 48 mm Ø tube to attach scaffold couplers.
Galvanized. Permits attachment of a guard-railing post at the MD panels and is used to form a stop end at the edge of the...
Galvanized. Permits attachment of a guard-railing post at primary and secondary beams and is used to form a stop end at the...
Coated. Is used as side railing at the slab edge and can be clamped to all kinds of beams or concrete slabs. Railing clamp...
Galvanized. Is used as hand-rail / mid-rail in combination with guard-railing post 48.
Galvanized. Connects 2 scaffold tubes with Ø 48,3 mm at any angle required.
Steel, painted. Sturdy steel mesh with reinforced edges and closed steel sheet to prevent small items from falling down. The...
Steel, painted. Height extension for safety mesh MFS. 500 kg impact protection. Meets the requirements as defined by...
Steel, galvanized. Connects safety meshes MFS at angles from 76° to 284°. Can be attached anywhere at the safety mesh.
Steel, galvanized. Is used to form slab ends for slabs up to 60 cm thick.
MEVA Formwork Systems Ltd.
Unit 2, Brabazon Court, Borman, Off Apollo Lichfield Industrial Estate, Tamworth
Staffordshire B79 7TA
United Kingdom
+44 1827 60217
+44 1827 60260
formwork.uk@meva-international.com
www.mevaformwork.co.uk